MR3020 + Webcam Logitech C170 + Motion = CCTV Sederhana

Kali ini akan saya sharingkan bagaimana cara membuat CCTV sederhana dengan menggunakan router dan webcam.

Peralatan yang saya gunakan:

1. Router TP-Link MR3020

2. Webcam Logitech C170
3. USB Hub Belkin 7 port

4. Flashdisk Kingston 8 GB

Referensi yang saya pakai ada di website :
http://sheldor.blogspot.com/2013/09/openwrt-based-video-recording-system.html
http://sheldor.blogspot.com/2013/09/openwrt-based-video-recording-system_10.html

Sesuai petunjuknya, mula-mula routernya di flash dengan OS OpenWRT dan di exroot.
Selanjutnya download file .rar berikut :
https://www.dropbox.com/s/bc417l2ty7sj9uv/Motion%2BFFMpeg.rar?dl=0

OS OpenWRT yang saya pakai adalah versi Attitude Adjustment. Versi Barrier Breaker seharusnya juga bisa dipakai.

Ekstrak file. rar yang telah di download tadi ke PC dan selanjutnya dengan menggunakan software Putty di transfer ke routernya.
Install semua file *.ipk - nya ke router dengan perintah di Putty :

opkg install *.ipk

Berikutnya adalah edit file konfigurasi aplikasi Motion nya yang ada di :
/etc/motion.conf  :

Thread 0

daemon = on

process_id_file = /var/run/motion/motion.pid

setup_mode = off

logfile = (not defined)

log_level = 4

log_type = all

videodevice = /dev/video0

v4l2_palette = 8

input = -1

norm = 0

frequency = 0

rotate = 0

width = 640

height = 360

framerate = 3

minimum_frame_time = 0

netcam_url = (not defined)

netcam_userpass = (not defined)

netcam_keepalive = off

netcam_proxy = (not defined)

netcam_tolerant_check = off

auto_brightness = on

brightness = 0

contrast = 0

saturation = 0

hue = 0

roundrobin_frames = 1

roundrobin_skip = 1

switchfilter = off

threshold = 5000

threshold_tune = off

noise_level = 32

noise_tune = on

despeckle_filter = (not defined)

area_detect = (not defined)

mask_file = (not defined)

smart_mask_speed = 0

lightswitch = 50

minimum_motion_frames = 2

pre_capture = 2

post_capture = 2

event_gap = 60

max_movie_time = 0

emulate_motion = off

output_pictures = off

output_debug_pictures = off

quality = 75

picture_type = jpeg

ffmpeg_output_movies = on

ffmpeg_output_debug_movies = off

ffmpeg_timelapse = 0

ffmpeg_timelapse_mode = daily

ffmpeg_bps = 200000

ffmpeg_variable_bitrate = 0

ffmpeg_video_codec = mpeg4

ffmpeg_deinterlace = off

use_extpipe = off

extpipe = (not defined)

snapshot_interval = 0

locate_motion_mode = off

locate_motion_style = redcross

text_right = %Y-%m-%d\n%T-%q

text_left = Logitech-C170

text_changes = on

text_event = %Y%m%d%H%M%S

text_double = on

exif_text = (not defined)

target_dir = /www/cctv

snapshot_filename = %v-%Y%m%d%H%M%S-snapshot

picture_filename = %v-%Y%m%d%H%M%S-%q

movie_filename = %Y-%m-%d--Jam-%H-%M-%S-Shot-%v

timelapse_filename = timelapse-tanggal-%d-%m-%Y

ipv6_enabled = off

stream_port = 0

stream_quality = 50

stream_motion = off

stream_maxrate = 3

stream_localhost = off

stream_limit = 0

stream_auth_method = 0

stream_authentication = (not defined)

webcontrol_port = 8081

webcontrol_localhost = off

webcontrol_html_output = on

webcontrol_authentication = (not defined)

track_type = 0

track_auto = off

track_port = (not defined)

track_motorx = 0

track_motorx_reverse = off

track_motory = 0

track_motory_reverse = off

track_maxx = 0

track_minx = 0

track_maxy = 0

track_miny = 0

track_homex = 128

track_homey = 128

track_iomojo_id = 0

track_step_angle_x = 10

track_step_angle_y = 10

track_move_wait = 10

track_speed = 255

track_stepsize = 40

quiet = on

on_event_start = (not defined)

on_event_end = (not defined)

on_picture_save = (not defined)

on_motion_detected = (not defined)

on_area_detected = (not defined)

on_movie_start = (not defined)

on_movie_end = (not defined)

on_camera_lost = (not defined)

video_pipe = (not defined)

motion_video_pipe = (not defined)

thread = No threads

Tinggal jalankan aplikasi dengan perintah :
motion

Aplikasi ini akan selanjutnya merekam video bila terdeteksi aktivitas dalam bentuk file *.avi . File video disimpan di router di folder /www/cctv

Contoh hasil rekaman adalah sebagai berikut :



Mula-mula saya sering mendapatkan rekaman video error seperti ini :

Ternyata solusinya cukup mudah tinggal edit file konfigurasi seperti diatas dengan :
lightswitch 50 .

Sekian dulu tutorialnya , semoga bermanfaat.